|
|
|
|
|
View previous topic :: View next topic |
Author |
Message |
sgtdclark
Joined: 10 Dec 2014 Posts: 2
|
Link Posted: Sun Oct 27, 2019 5:23 pm Post subject: HLT side has no power |
|
|
Turned panel on. Boil and mash PIDs powered on as usual. HLT did not. Tried turning element on and nothing still and the indicator light for the element would not activate. Switched HLT probe to mash probe port and flipped to the boil power. Element turned on. I have traced all the wires. Nothing is melted or disconnected. This was built by TheElectricBrewery so I have absolutely no knowledge of any of the components. I will manage my brew day by flipping power and probes but does anyone have any thoughts on what component or components are bad. I did have a little issue a few months back where the breaker when bad and was tripping frequently. I replaced it and have brew five or six times since so not sure if that may have caused an issue on this side.
|
|
Back to top |
|
|
kal Forum Administrator
Joined: 12 Dec 2010 Posts: 11122 Location: Ottawa, Canada
Drinking: Pub Ale, Electric Creamsicle, Mild, Pliny the Younger, Belgian Dark Strong, Weizen, Russian Imperial Stout, Black Butte Porter
|
Link Posted: Sun Oct 27, 2019 5:56 pm Post subject: |
|
|
Hi Dan!
I received the emails you sent as well. Thanks for the pictures. This is a pre-assembled control panel you purchased from us in 2014. The HLT PID appears to have died (it's not lighting up at all). It should be replaced. Replacements are available here: https://shop.theelectricbrewery.com/collections/temperature-controllers/products/syl-2352-pid-temperature-controller
To replace all that is required is a screwdriver. I suggest using pieces of tape to make the wires so that you re-attach in the same spots. Make sure to unplug the panel from the wall outlet before replacing the PID.
Once installed make sure to set up the PID per the control panel setup instructions here: http://www.theelectricbrewery.com/control-panel-setup
The whole swap takes 5 minutes.
As our control panels have redundant components between the boil and HLT sides, you may still continue to use it by swapping cords until you have your replacement PID.
Cheers!
Kal
_________________ Our new shop with over 150 new products: shop.TheElectricBrewery.com
We ship worldwide and support our products and customers for life.
Purchasing through our affiliate links helps support our site at no extra cost to you. We thank you!
My basement/bar/brewery build 2.0
Last edited by kal on Sun Oct 27, 2019 6:07 pm; edited 1 time in total
|
|
Back to top |
|
|
kal Forum Administrator
Joined: 12 Dec 2010 Posts: 11122 Location: Ottawa, Canada
Drinking: Pub Ale, Electric Creamsicle, Mild, Pliny the Younger, Belgian Dark Strong, Weizen, Russian Imperial Stout, Black Butte Porter
|
Link Posted: Sun Oct 27, 2019 6:05 pm Post subject: |
|
|
Order received! We'll get your replacement PID out ASAP. Cheers!
Kal
_________________ Our new shop with over 150 new products: shop.TheElectricBrewery.com
We ship worldwide and support our products and customers for life.
Purchasing through our affiliate links helps support our site at no extra cost to you. We thank you!
My basement/bar/brewery build 2.0
|
|
Back to top |
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
Forum powered by phpBB © phpBB Group
|
|