|
|
|
|
|
View previous topic :: View next topic |
Author |
Message |
d2024p
Joined: 25 Oct 2018 Posts: 4
|
Link Posted: Thu Oct 25, 2018 2:32 pm Post subject: Metal vs plastic ducting |
|
|
Hello,
First I want to say the TEB is incredible. I have used it as a resource to plan the extractor system for a new brewery. This is going to be a glass and steel home office design which will house a 100l setup. The unit is already in place and I am excited about getting the extractor system set up so I can start using it!
There is one thing I wanted to clear up and I really hope someone might be able to help. The ventilation guide on the website says to only use metal ducting, and I have been trying hard to stick to this. The problem is that stainless is really expensive. I have to buy three metres (9ft) from any of the small number of UK suppliers that stock stainless over galvanized. Because I just need to drill a hole anywhere in the steel shell for the outward vent I can get away with a very short duct run, (2-3 feet max) so I would be wasting at least six feet of duct.
I am not sure I want to go for galvanized steel because I am worried about corrosion and food safety. I may want to go semi-commercial in the future and don't want to have to replace the ductwork to conform. I want a stainless hood and I know where to get one reasonably cheap, but I am worried that even with a condensation trap I will get some tainted condensate coming back from the galvanized duct.
So.. I was wondering why the guide on the website says not to use plastic. Can anyone shed any light? Apart from the fact that steel looks cool Plastic would have advantages for me such as price, availability of 1m lengths, self-insulation and the fact that it's easy to work with. Can anyone shed any light please? Any assistance would be gratefully appreciated.
If I were to get plastic just to get the vent through the 'wall' cavity, does anyone know if I can join six inch plastic to six inch steel? Or does it have to be 100% one way or another?
Cheers!
|
|
Back to top |
|
|
kal Forum Administrator
Joined: 12 Dec 2010 Posts: 11122 Location: Ottawa, Canada
Drinking: Pub Ale, Electric Creamsicle, Mild, Pliny the Younger, Belgian Dark Strong, Weizen, Russian Imperial Stout, Black Butte Porter
|
|
Back to top |
|
|
kal Forum Administrator
Joined: 12 Dec 2010 Posts: 11122 Location: Ottawa, Canada
Drinking: Pub Ale, Electric Creamsicle, Mild, Pliny the Younger, Belgian Dark Strong, Weizen, Russian Imperial Stout, Black Butte Porter
|
Link Posted: Thu Oct 25, 2018 3:10 pm Post subject: |
|
|
Instructions (and ebook) updated:
http://www.theelectricbrewery.com/ventilation?page=6
The most pertinent part:
Note: There's absolutely no reason to use stainless here. Galvanized steel is fine, as is PVC rated for this. PVC is more expensive. One benefit of PVC is if the seams are properly cemented together, you don't need to tape the seams.
Cheers!
Kal
_________________ Our new shop with over 150 new products: shop.TheElectricBrewery.com
We ship worldwide and support our products and customers for life.
Purchasing through our affiliate links helps support our site at no extra cost to you. We thank you!
My basement/bar/brewery build 2.0
Last edited by kal on Thu Oct 25, 2018 3:21 pm; edited 1 time in total
|
|
Back to top |
|
|
d2024p
Joined: 25 Oct 2018 Posts: 4
|
Link Posted: Thu Oct 25, 2018 3:20 pm Post subject: |
|
|
Hi Kal,
That's really good of you, thanks so much. I was kind of looking forward to some professional looking stainless but I just can't justify the cost, not at the moment. I just need to keep telling myself that it's a working unit and it is build for functionality and practicality! So PVC-rated plastic will do just fine at a fraction of the cost.
I completely understand why flexible ducting would be ill-advised at best and downright disastrous at worst. The impact that it would have on suction and with a 5kwh of wort vapor going through during a boil I can see it getting absolutely saturated and, let's face it, staying that way.
Whilst I am typing I have remembered one related but separate question, if that's OK. I am getting an in-line centrifugal fan like the one you recommend but due to the length of the duct run I might need to install it on the vertical axis, so that the blades are horizontal. Yours is the opposite (for good reason, in your case). Do you see a problem with 'opposite' approach?
Keep up the good work and if there is any way I can contribute to the site please let me know.
Cheers!
|
|
Back to top |
|
|
kal Forum Administrator
Joined: 12 Dec 2010 Posts: 11122 Location: Ottawa, Canada
Drinking: Pub Ale, Electric Creamsicle, Mild, Pliny the Younger, Belgian Dark Strong, Weizen, Russian Imperial Stout, Black Butte Porter
|
Link Posted: Thu Oct 25, 2018 3:27 pm Post subject: |
|
|
d2024p wrote: | Whilst I am typing I have remembered one related but separate question, if that's OK. I am getting an in-line centrifugal fan like the one you recommend but due to the length of the duct run I might need to install it on the vertical axis, so that the blades are horizontal. Yours is the opposite (for good reason, in your case). Do you see a problem with 'opposite' approach? |
The biggest issue is that some condensation will likely form, and with my placement as mentioned in the instructions I allow for a drip hole to let this moisture escape in a controlled manner. If you install it vertically (up/down) instead of horizontally (left/right) I'm not sure where this condensation will end up.
Insulating the duct will minimize condensation as it'll keep the steam hot, but it all depends on the run length, ambient temp, and so forth.
My run is short (probably around 6 feet or so) not insulated, and i get about half a cup of water that drips out of the fan over a 60 min boil.
Quote: | Keep up the good work and if there is any way I can contribute to the site please let me know. |
Thanks for kind words! Lots of ways to contribute!:
(1) Buy something from our shop: https://shop.theelectricbrewery.com/
(2) Buy something from our affiliates: http://www.theelectricbrewery.com/forum/viewtopic.php?t=24489
(3) Sign up for a club membership: http://www.theelectricbrewery.com/forum/viewtopic.php?t=24536
Cheers!
Kal
_________________ Our new shop with over 150 new products: shop.TheElectricBrewery.com
We ship worldwide and support our products and customers for life.
Purchasing through our affiliate links helps support our site at no extra cost to you. We thank you!
My basement/bar/brewery build 2.0
|
|
Back to top |
|
|
d2024p
Joined: 25 Oct 2018 Posts: 4
|
Link Posted: Thu Oct 25, 2018 4:04 pm Post subject: |
|
|
kal wrote: | The biggest issue is that some condensation will likely form, and with my placement as mentioned in the instructions I allow for a drip hole to let this moisture escape in a controlled manner. If you install it vertically (up/down) instead of horizontally (left/right) I'm not sure where this condensation will end up.
Insulating the duct will minimize condensation as it'll keep the steam hot, but it all depends on the run length, ambient temp, and so forth.
My run is short (probably around 6 feet or so) not insulated, and i get about half a cup of water that drips out of the fan over a 60 min boil.
Kal |
Thanks Kal! My run will be so short that I don't expect there to be much at all, so I'm hoping that one of these where the duct meets the extractor hood (allowing me to neatly run the condensation out in a pipe running along the hood) will do the trick.
https://www.amazon.co.uk/condensation-diameter-hydroponics-ventilation-extractor/dp/B00BW31SA0/ref=as_li_ss_tl?ie=UTF8&linkCode=ll1&tag=curpalcrtproa-21&linkId=74915f09025aa50568ed02fe12511959&language=en_GB
I'll sign up for a year's membership, it's the least I can do given all the advice your site gave me!
|
|
Back to top |
|
|
kal Forum Administrator
Joined: 12 Dec 2010 Posts: 11122 Location: Ottawa, Canada
Drinking: Pub Ale, Electric Creamsicle, Mild, Pliny the Younger, Belgian Dark Strong, Weizen, Russian Imperial Stout, Black Butte Porter
|
Link Posted: Thu Oct 25, 2018 5:26 pm Post subject: |
|
|
Sounds like a plan! As long as the ducts are angled properly such that any condensation runs in the right direction you're good.
Thanks for signing up!
Kal
P.S. I also changed your Amazon link to support our forum/site.
_________________ Our new shop with over 150 new products: shop.TheElectricBrewery.com
We ship worldwide and support our products and customers for life.
Purchasing through our affiliate links helps support our site at no extra cost to you. We thank you!
My basement/bar/brewery build 2.0
|
|
Back to top |
|
|
d2024p
Joined: 25 Oct 2018 Posts: 4
|
Link Posted: Thu Jun 11, 2020 3:11 pm Post subject: |
|
|
kal wrote: | Sounds like a plan! As long as the ducts are angled properly such that any condensation runs in the right direction you're good.
Thanks for signing up!
Kal
P.S. I also changed your Amazon link to support our forum/site. |
Hi Kal,
Thanks again for everything your site has taught me about building an electric brewery, from element sizing to ventilation to the need for some sort of shop vac (I went for a wet and dry) . I thought you might want to see photos of the final build (forgive the quality), if only to see one of the shortest duct runs you are ever likely to!
To recap the basics of my system:
100L HLT with high-flow HERMS coil and 5.5KW round element
100L MT
100L BK with 5.5KW round element and cold side Tri-clamp
Brewery controller provided by a UK supplier (Einbrew 3v3P)
I should just be able to scale up to 200L in the future and still fit everything on the brew stand
Anyway, I doubt I could have done it without your site and forum so thanks again and cheers I have finally purchased the 1y site membership I promised to as well.
Description: |
|
Filesize: |
167.69 KB |
Viewed: |
9697 Time(s) |
|
Description: |
|
Filesize: |
141.52 KB |
Viewed: |
9697 Time(s) |
|
Description: |
|
Filesize: |
55.68 KB |
Viewed: |
9697 Time(s) |
|
|
|
Back to top |
|
|
kal Forum Administrator
Joined: 12 Dec 2010 Posts: 11122 Location: Ottawa, Canada
Drinking: Pub Ale, Electric Creamsicle, Mild, Pliny the Younger, Belgian Dark Strong, Weizen, Russian Imperial Stout, Black Butte Porter
|
Link Posted: Thu Jun 11, 2020 3:28 pm Post subject: |
|
|
Nice setup! Thanks for sharing and thanks again for supporting us through a forum club membership - it's appreciated!
Kal
_________________ Our new shop with over 150 new products: shop.TheElectricBrewery.com
We ship worldwide and support our products and customers for life.
Purchasing through our affiliate links helps support our site at no extra cost to you. We thank you!
My basement/bar/brewery build 2.0
|
|
Back to top |
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
Forum powered by phpBB © phpBB Group
|
|