Return to TheElectricBrewery.com
  [ Shop ]   [ Building ]   [ Using ]   [ Recipes ]   [ Testimonials ]   [ Gallery ]   [ FAQ ]   [ About Us ]   [ Contact Us ]   [ Newsletter ]

Log inLog in   RegisterRegister   User Control PanelUser Control Panel   Private MessagesPrivate Messages   MembershipClub Memberships   SearchSearch   MemberlistMemberlist   Photo AlbumsPhoto Albums   Forum FAQForum FAQ

TheElectricBrewery.com Forum Index -> Photo Albums -> mnoltimier Goto page 1, 2  Next
mnoltimier
Title: My Electric Brewery... almost done!
Posted: Tue Aug 14, 2012 6:57 pm
Views: 658
Comments: 0
Title: DIY Control Panel Kit
Posted: Tue Aug 14, 2012 6:58 pm
Views: 294
Comments: 0
Title: DIY Temp probe kit
Posted: Tue Aug 14, 2012 6:58 pm
Views: 239
Comments: 0
Title: The expandable sleeving sucks to put on... patience.
Posted: Tue Aug 14, 2012 6:59 pm
Views: 247
Comments: 0
Title: Temp probes done.
Posted: Tue Aug 14, 2012 7:00 pm
Views: 223
Comments: 0
Title: Heating element power cords.
Posted: Tue Aug 14, 2012 7:01 pm
Views: 220
Comments: 0
Title: Heating element kit.
Posted: Tue Aug 14, 2012 7:01 pm
Views: 226
Comments: 0
Title: Heating element power cords assembled.
Posted: Tue Aug 14, 2012 7:02 pm
Views: 237
Comments: 0
Title: Back plate of control panel getting drilled.
Posted: Tue Aug 14, 2012 7:02 pm
Views: 229
Comments: 0
Title: Back plate of control panel getting tapped.
Posted: Tue Aug 14, 2012 7:03 pm
Views: 224
Comments: 0
Title: Sure were a lot of holes to tap.
Posted: Tue Aug 14, 2012 7:03 pm
Views: 239
Comments: 0
Title: Back plate ready for wiring. I went to my local Ace Hardware store and picked up nylon screws for the DC power supply instead of the metal ones included in the kit. People were having problems with it shorting out.
Posted: Tue Aug 14, 2012 7:05 pm
Views: 233
Comments: 0
Title: Heat element box drilled.
Posted: Tue Aug 14, 2012 7:06 pm
Views: 207
Comments: 0
Title: Holes for panel measured.
Posted: Tue Aug 14, 2012 7:06 pm
Views: 217
Comments: 0
Title: Panel front cut. Buy the tools Kal says to get. If you don't you will screw up your panel AND your kettles. I can not stress how important the correct tools have been.
Posted: Tue Aug 14, 2012 7:07 pm
Views: 214
Comments: 0
Title: Progress...
Posted: Tue Aug 14, 2012 7:08 pm
Views: 229
Comments: 0
Title: Bottom holes cut.
Posted: Tue Aug 14, 2012 7:09 pm
Views: 233
Comments: 0
Title: Everything fits perfectly!
Posted: Tue Aug 14, 2012 7:09 pm
Views: 234
Comments: 0
Title: Handles installed.
Posted: Tue Aug 14, 2012 7:10 pm
Views: 224
Comments: 0
Title: Heat sink hole cut.
Posted: Tue Aug 14, 2012 7:10 pm
Views: 235
Comments: 0
Title: All holes cut!!! Phew... that was a big job.
Posted: Tue Aug 14, 2012 7:11 pm
Views: 231
Comments: 0
Title: Heat sink installed. Go very very slowly when tapping the holes in the heat sink. A drill press is a MUST for this job.
Posted: Tue Aug 14, 2012 7:12 pm
Views: 240
Comments: 0
Title: SSR's installed into heat sink. I needed to use some small washers because the screws were too long.
Posted: Tue Aug 14, 2012 7:13 pm
Views: 244
Comments: 0
Title: Optimus Primed!
Posted: Tue Aug 14, 2012 7:13 pm
Views: 227
Comments: 0
Title: First heat element installed. Buying the expensive Green Lee tools is a MUST. You will screw up your kettles without them. The correct tools made this job really really easy. I was nervous though ~~~
Posted: Tue Aug 14, 2012 7:14 pm
Views: 244
Comments: 0
Title: A look inside...
Posted: Tue Aug 14, 2012 7:15 pm
Views: 226
Comments: 0
Title: Painted. The paint instructions said to paint in a humid free area. I live in Houston... good luck finding that.
Posted: Tue Aug 14, 2012 7:16 pm
Views: 244
Comments: 1
Title: Front panel buttons installed.
Posted: Tue Aug 14, 2012 7:16 pm
Views: 254
Comments: 0
Title: A look at my layout.
Posted: Tue Aug 14, 2012 7:17 pm
Views: 218
Comments: 0
Title: Tags installed.
Posted: Tue Aug 14, 2012 7:17 pm
Views: 234
Comments: 0
Select sort method:  Order:  
   TheElectricBrewery.com Forum Index -> Photo Albums -> mnoltimier All times are GMT
Goto page 1, 2  Next
Page 1 of 2


Support our site by purchasing through this link. We thank you!

Forum powered by phpBB © phpBB Group